|
Award Levels
|
Credit Hours Required
|
Time to Completion
|
|
Level 1 Certificate
|
18
|
1 Year
|
|
Level 2 Certificate
|
32
|
2 Years
|
|
Associate of Applied Science
|
64
|
2 Years
|
The Construction Technology program allows students the opportunity to complete certificates at two levels and to transfer these certificates toward an Associate of Applied Science degree in Industrial Engineering Technology. The Level I Construction Technology certificate is for students who intend to seek entry-level employment after completing a one-year program of study. The Level II certificate is for students interested in advancing their skill level beyond Level I.
The curriculum utilizes National Center for Construction Education and Research (NCCER) a nationally-recognized credentialing and certification system. This National Registry system assures portability of skills by providing transcripts, certificates, and wallet cards to students who successfully complete the program.
Career areas can include carpenter, electrician, brick and block mason, plumber, drywall installer, construction laborer, construction supervisor and more.
|
|
|
|
Interested in this program?
Contact an Advisor!
outreach@neosho.edu
(620)432-0406
|
Recommended Sequence of Courses
|
(Fall) Semester I
|
|
Credit Hours
|
|
CMCT 105
|
OSHA 10 Safety Orientation
|
1
|
|
CMCT 106
|
Introduction to Craft Skills
|
3
|
|
CMCT 107
|
Carpentry Basics
|
4
|
| |
Total
|
8
|
|
(Spring) Semester II
|
|
|
|
CMCT 110
|
Floors, Walls & Ceiling Framing
|
4
|
|
CMCT 111
|
Roof Framing
|
3
|
|
CMCT 112
|
Windows, Doors and Stairs
|
3
|
| |
Total
|
10
|
|
Level I Certificate Credits
|
18
|
|
(Fall) Semester III
|
|
|
|
CMCT 205
|
Site Layout & Handling & Placing Concrete
|
4
|
|
CMCT 206
|
Drywall, Window, Door & Ceiling Install
|
2
|
| |
Total
|
6
|
|
(Spring) Semester IV
|
|
|
|
CMCT 210
|
Roofing & Exterior Finishes
|
4
|
|
CMCT 211
|
Electrical, HVAC, Drain, Waste & Vent
|
4
|
| |
Total
|
8
|
|
Level II Certificate Credits
|
32
|
|
Associate of Applied Science Degree Program Credits
Students interested in completing an Associate of Applied Science degree in Industrial Engineering Technology with an emphasis in construction should visit with an advisor to determine general education and additional technical education requirements. Degrees require completion of 64 credit hours.
|
64
|
Additional Information
An articulation agreement between NCCC and Pittsburg State University means that 100% of your NCCC AAS degree in Industrial Engineering Technology will transfer toward the PSU Bachelor of Applied Science in Technology degree. If you wish to transfer to PSU, please note the requirements summarized in the transfer guide:
Pittsburg State University Articulation Agreement
Pittsburg State University Transfer Guide
Program Outcomes
(Level I)
- Demonstrate the fundamentals of OSHA and the knowledge of basic safety.
- Demonstrate the ability to perform construction math.
- Demonstrate the ability to correctly use construction tools.
- Demonstrate the ability to utilize construction drawings.
- Demonstrate basic rigging techniques.
- Demonstrate basic communications and employability skills.
- Demonstrate basic knowledge of carpentry trade.
- Demonstrate the ability to layout and construct floor, wall, ceiling, and roof framing.
- Demonstrate the ability of roof framing techniques.
- Demonstrate the ability of window and door installation.
(Level II)
- Demonstrate the knowledge of construction site layout, and the handling and placement of concrete.
- Demonstrate the ability of interior material applications.
- Demonstrate the ability of exterior material applications.
- Demonstrate the basic knowledge of electrical, HVAC, drain, waste, and vent systems.
